-
Legs are sold individually and include a 2" aluminum tube, footpad, and post cap. Rampit USA recommends purchasing legs longer than the needed application to allow for adjustments. We also recommend a diagonal brace for legs exceeding 48" in height. -
Platform handrails are sold individually and specifically designed to fit Rampit USA Platforms. The actual length of each handrail, measured end to end, is shown in the chart below. Platform handrails include two handrail posts and two filler tubes for lengths 4' - 8' or three handrail posts and four filler tubes for lengths 9' and 10'. Platform handrails do not include ninety-degree corners or plastic knuckles for connecting multiple handrails.Handrail Length Actual Length 4' 3' 4 1/2" 5' 4' 4 1/2" 6' 5' 4 1/2" 7' 6' 4 1/2" 8' 7' 4 1/2" 9' 8' 5" 10' 9' 5" -
Ramp handrails are sold as a set and specifically designed to fit Rampit USA Independence Series Ramps. Ramp handrails are actual size measured from end to end. Each handrail (2 per set) includes two handrail posts and two filler tubes for lengths 4' - 8' or three handrail posts and four filler tubes for lengths 9' and 10' only. Ramp Handrails include a small bolt pack for installation. Square ends, ANSI Loops, Knuckles, Corners, Caps, and inserts needed for terminating or changing handrail direction are all sold separately. -
Light tread is sold by the foot and comes standard on all residential platforms and portable ramps. When ordering, please select the length of tread needed and the quantity. For ramp tread, please see medium tread. Please contact us for custom lengths not listed below. -
A support assembly is made up of a crossarm, including two leg clamps and two crossarm clamps, and two complete legs. Support assemblies are installed underneath a ramp and are used to connect two individual ramp sections. -
ANSI loops are the rounded ends of Rampit USA handrails. ANSI loops include pre-installed aluminum inserts (not pictured) and can be flipped to angle upwards or downwards. -
Square ends are used to enclose and terminate the end of a handrail when space may be an issue. Square ends are sold individually and include pre-installed aluminum inserts (not pictured). Rampit USA recommends using ANSI loops whenever space allows. -
Aluminum inserts are inserted into the open ends of handrail components to create a secure connection between various components. -
Plastic knuckles are inserted directly into the open end of two handrail components to create a corner that may not be exactly 90-degrees. -
Large bolt packs contain enough hardware for installing six handrail posts:- (12) 1" x 5/16" Carriage Bolts
- (6) 2" x 5/16" Carriage Bolts
- (18) 5/16" Washers
- (18) 5/16" Hex Nuts
-
All Rampit USA ramps are attached to platforms using aluminum adapters attached to the ramp’s stringers. These adapters are reversible and can be used for ramps that go up or down. Each adapter pack includes two sets of adapters and hardware:- (2) Aluminum Adapters
- (2) Angle Brackets
- (6) 1" x 5/16" Carriage Bolts
- (6) 5/16" Washers
- (6) 5/16" Hex Nuts
- (2) 1/4" x 1/2" Self-Tapping Screws
-
All Rampit USA aluminum ramps and platforms are assembled using a series of inter-connected pieces of light and/or medium tread. Medium tread is sold by the foot and comes standard in all Rampit USA ramps and commercial platforms. Please note: there are two different types of medium tread in all Rampit USA ramp sections. The first piece of tread is open on the front and the back and is known as starter tread. All remaining tread on a ramp section is standard medium tread, which is open on the front but closed on the back. When ordering, please select the type of tread, the length needed, and the quantity. For standard platform tread, please see light tread. Please contact us for custom lengths not listed below.